60V-72V 4000W-5000W 80A Sine Wave Intelligent Controller with Colorful LCD Display for eBike Electric Bike
Very important Notice:
This controller can
only work without display or
with our display, please never use it with your own display (because program is different)
Why Self-learning Controller?
Self-learning Function:
(1). Wrong color wires combination of 5-hall sensor wires (
But please ensure hall sensor is good, red and black hall sensor wires must be connected correctly) between motor and controller, doesn’t matter, self-learning process can correct it!
(2). Wrong color wires combination of 3-phase wires between motor and controller, doesn’t matter, self-learning process can correct it!
Parts Including:
1. 18 MOSFET 60V 72V Universal Voltage 4000W-5000W Intelligent Sine Wave Controller
2. XT150 Male Connectors x 3pcs, QS8 Female Connector x 1pc
3. 36V, 48V, 52V, 60V, 72V UKC1 Colorful Display (Optional)
Advantage:
1. Sine Wave Controller which support self-learning and smart match with each motor through self-learning, works with high efficiency, less noise, and lower energy consumption, which makes your electric vehicles or electric motorcycles more comfortable and easier to control, give you best pedal experience
2. Universal Input Voltage Range: 60V/72V
3. Work with or without display
4. Parameter setting via display
5. All protection make it long life and safe: over/under voltage, over current, over load, over heating, anti-runaway, locked-motor protection
6. Multi functions: Work with hall sensor mode or non-hall mode, smart match with different motor, 3/5/9-speed level for throttle and PAS, Current limit, Speed limit, Reverse, Push Assistant, Anti-thief, Regenerative Braking (Can set different level: Off, Standard, Weak, Strong), Speed detecting (Magnet quantity simulated or internal speed sensor) and etc.
7. Best heat sinking with Aluminium Case
8. Black anodized Aluminium Controller Case against scratch
Technical Data:
General Specification:
1. Rated Power: 60V 2400W/ 72V 2880W
2. Peak Power: 60V 4800W/ 72V 5760W
3. Brake: Low Voltage Brake
4. Alarm: Low Voltage Alarm
5. Rotor Position Detecting Method: Hall sensor
6. 3-Phase Connectors: XT150 Female Plugs
7. Power Input Connector: QS8 Male Plug
8. 3-Phase and Power Input Cable Size: 8AWG (8mm2)
9. Size: 208x107x60mm
10. Net Weight: 1200g
11. Waterproof Grade: IP65
LCD Specification: 3.5 inch IPS screen
1) Input Voltage: 24V/36V/48V/52V/60V/72V
2) Rated operating power: 1W
3) Max operating power: 5W
4) USB charging port: 5V 500mA
5) Off leakage current: < 1uA
6) Support current to controller: 100mA
7) Size: 111.1*66.8*82.8mm
8) Waterproof grade: IP65
9) Operating temperature: -20~70℃,
10) Storage temperature: -30~80℃
FAQ:
1. How shall I match my motor for first time use? (Very Important)
(Please check
Controller Connection Diagram and Manual, Page 1)
1). Lift your motor wheel off ground (
very important)
2). If you connect with display, please make sure PAS/Throttle Speed Level is at any level more than 0 level
3). Connect Self-learning plug 6-8 seconds
4). You will see motor wheel rotate slowly
5). Please check whether rotation direction is correct
(a). If correct direction, then keep 6-8 seconds, then disconnect
(b). If reverse direction, then disconnect and plug again till get correct rotation direction, then keep 6-8 seconds, then disconnect
6). Motor and Controller Pairing finished!
2. Can I use this controller without display?
Yes, you can use this controller without display, just need to connect jumper connector (Please check
Controller Connection Diagram and Manual, Page 4, point No.3). But if you want to have and change ABS setting (Reg. function) and use Cruise function, have to buy our UKC1 display together.
3. How can I limit speed?
In some countries, below 25km/h speed is required on road, you can switch on/off speed limit function by connecting a simple switch to controller speed limit plug, or you can even connect jumper connector to always limit speed (Please check
Controller Connection Diagram and Manual, Page 6, point No.8)
4. How can I active Regenerative braking function?
This function need to use together with UKC1 display, please enter "Advanced Setting", there is "ABS Levels" option (0-3). "0" means turn off; "1" means weak; "2" means standard; "3" means strong--- we don't recommend to use 3, it is too strong, we will not be responsible for controller or motor damage due to this setting (ABS level=3)
5. How can I use cruise function?
This function need to use together with UKC1 display, please keep throttle at speed not change, and long press "Down" key at same time will active cruise function, press any key or operate brake or throttle to change speed will stop Cruise function.
Manual Download:
1.
Controller Connection Diagram and Manual Download
2.
UKC-1 Display Manual Download